ClearView Plastics and Composites in Rocklin

Review №1

2024-01-27 04:26:03

Needed a case for my A1 because I keep it in the basement and the temperatures fluctuate quite a bit. Searched enclosure on the inter webs and ClearView popped up.I had several, okay, a ton of questions and concerns about the enclosure and how it would affect the printer and such but found comfort and manners in Neil’s help. Genuinely remained patient while I asked all of my questions and guided me along the purchase. Will 100% use their services again.

Review №2

2023-10-06 01:27:05

Just finished installing the Medium sized SLA Resin 3D Printer Enclosure V2.0 and I have to say its VERY nice. Went together without much fuss. It’s in my basement and vented outside via a garden well. Very happy with my purchase.What amazes me is how close the tolerances are. The doors open and close with less than 1 mm to spare. Loving it! Inside is the Anycubic Photon Mono M5s. It’s a perfect fit for this enclosure.

Review №3

2023-01-13 19:41:06

I bought the clearview for my xtool d1 pro. I recieved it in two days. The items in the box were all in good condition. It took me about 8 hours to to assemble it. I have been using it for about 3 weeks now and had only one problem. One the the hinges broke on me. They sent me 3 replacements. I like the product and the service.

Review №4

2022-02-25 18:49:32

Just completed assembly and installation of my Laser Engraver enclosure! Works like a charm! The folks at Clearview were extremely knowledgeable, answered all of my questions, and helped me to feel confident in purchasing the correct enclosure for my Laser Engraver!

Review №5

2022-06-29 20:46:52

Purchased and constructed the Ender S1 enclosure with carbon filter.Box went together all right the instructions were clear, however the flat rivet type screws were more then a nuisance to screw together, once I figured out the correct technique it wasnt too bad though.Be prepared to print washers for the hinges of the door otherwise it will not work properly. Too much slop otherwise. Ordered the pre-printed parts to save time, a few of which came with obvious defects worst of all was the carbon filter. The filter was completely sheared from the 3D part on arrival, and the fan had obvious print defects. I contacted customer service and have yet to hear a reply. Instead, I took 5 minutes and designed a far better alternative, attached it and now have the carbon filter working correctly.All-in-all, good box, quality of the prints and of the customer service does not justify the price tag at all IMO.

Review №6

2024-02-27 20:25:24

Enclosure is amazing, tolerances are on point, quality is top notch. Would highly recommend for any 3D printer to reduce noise and air pollution.

Review №7

2024-03-13 16:08:30

Neil and his team did a stellar job getting my order ready and shipped super quick. Needed a 4 pin cable and they got it to me ASAP.

Review №8

2021-09-27 16:41:36

I ordered an enclosure for my Prusa I3 printer from Clearview Plastics. It was very easy to assemble and the accuracy of the parts fitting together was exceptional, and the quality of the materials was very good.The people at the company were very helpful and prompt with their responses.I would recommend the company to anyone needing their services.

Review №9

2022-07-08 12:30:35

I ordered a custom enclosure for my ender 3 s1 pro and couldnt be happier, the quality of the clearview plastic enclosure is unmatched, the hardware included is the highest quality. Assembly was straightforward, shipping was fast, highly recommend.

Review №10

2022-06-03 22:10:05

I ordered an enclosure for my xtool D1, received it and after many struggles I have it shakily assembled! Here are my dislikes: the rivets flat back also needs a Philips insert because a finger on the smooth back does not always work for tightening, the top lid is slightly heavy and has no way to stay open, the inner space is so tight around the laser frame that you have no room to run the wires for the fan I purchased from you or the led lights, you gave no hint as to where and how to install the lights and run the wires, the fan you sold me had no indent for the power wire to allow it to mount flat on the plexiglass without crimping the wire so I had to customize it and the screws were too short to mount the fan so I had to get longer ones. So, it looks great but has some fairly major flaws!